Yashas Enterprises

Latapoxy grout for floor n'wall
Latapoxy part C filler powder to be used in combination with part A (hardener) and part B (resin)

It is a polymer-based adhesive designed for fixing ceramic tiles and small format natural stones on dry areas of interior floors.

Features and Benefits:

For fixing cermic tiles on interior floor & wall

Ideal for new floor tiling

Economical & easy to use

Single component - Just add water

Coverage: Approx. 55-60 Sft per 20 Kg pack, using 1/4?? x 1/4?? (6mm x 6mm) square notched trowel for a bed of 3mm. 

Working Properties at 70° F (21° C) 
LATAFIX 305 Adhesive mixed with Water 
Pot Life 2 - 3 Hours Time to Heavy Traffic 16 - 24 hours 

COLOUR-GREY

Additional Information:

• Item Code: 32141000
• Packaging Details: 20 KG AND 30 KG ,COLOUR-GREY

MYK LATICRETE SP-100™ Tile Joint is a Stain Resistant, Water Resistant & Germ Resistant grout for Floor & Wall. MYK LATICRETE SP-100 Tile-Joint is suitable for ceramic tiles, vitrified tiles, marble and stone, especially in stain prone areas such as kitchens and washrooms.
Features & Benefits:
100% Stainfree
Strong and durable
Chemical and temperature resistant
Anti-bacterial and anti-fungal

A single-component, hybrid grout that is UV-resistant and suitable for both interior and exterior applications.
Colour: Available in 10 colours

A polymer-based, un-sanded cement grout for interior and exterior tile joints.

Description 

• Dwa 215  Is A Modified Polyurethane Adhesive Designed For The Installation Of Glass Mosaic Tile, Ceramic Tile, Vitrified Tile And Natural Stone On Most Drywall Boards And Clean Dry Cement Based Surfaces. Dwa 215 Is A Factory Made Pail Consisting Of Pre-blended Single Component Adhesive Which Is Ready To Use. Off White Certification Ansi A 118.4 & 136.1En:12004/Iso 13007:D2TeVoc: Very Low
• How To Apply: Apply Adhesive To The Substrate With The Flat Side Of The Trowel, Pressing Firmly To Work Into Surface. Comb On Additional Adhesive With The Notched Side. Use The Proper Sized Notched Trowel To Insure Full Bedding Of The Tile. Spread As Much Adhesive As Can Be Covered With Tile In 10 Minutes. Back Butter Large Tiles (> 12"X12") To Provide Full Bedding And Firm Support. Place Tiles Into Wet, Sticky Adhesive And Beat In Using A Beating Block And Rubber Mallet To Imbed Tile And Adjust Level. Check Adhesive For Complete Coverage By Periodically Removing A Tile And Inspecting Bedding Adhesive Transfer Onto Back Of Tile. If Adhesive Is Skinned Over (Not Sticky), Remove And Replace With Fresh Adhesive. Areas Of Application For Commercial And Residential Installations Of Ceramic Tile, Vitrified Tile And Natural Stone Over Most Drywall Boards And Clean Cement Based Surfaces. Used Where Installations Must Resist Physical Abuse, Shock, And Mild Chemicals. (Interior & Exterior)   Suitable Substrates ConcreteCement Mortar Beds Plywood Gypsum Wall Board Calcium Silicate Board Bison Panel Board Concrete Masonry Cement Plaster Aac Block Masonry Cement Terrazzo Cement Backer Board Existing Ceramic Tile Other Resilient Tile And Stone All Cement Based Surfaces Should Have Been Cured As Per Standard Practices And Shall Be Dry For Tiling Consult Cement Backer Board Manufacturer For Specific Installation Recommendations And To Verify Acceptability For Exterior Use. Note: Not For Use On Metal & Plastic Substrates And Metal Tiles. 

Features

•  Single Component, Just Open And Use.
•  High Strength. 
•  Economical & Easy To Use
• Bonds To Various Substrates
• Exceeds Ansi A136.1 Shear Bond Strength Requirements & Is 15477 : 2019 Requirements. 
• Complies With En / Iso With A D2Te Classification. 
• Water And Shock Resistant. Modified Polyurethane Adhesive For Fixing Ceramic, Semi Vitrified Tile, And Natural Stone On Various Types Of Drywall Boards And Clean Dry Cement Surfaces Substrates
• Concrete & Concrete Masonry
• Mivon Concrete, Vdf, Tremix Concrete
•  Cement Mortar Beds* & Cement Plaster
• Aac Block Masonry Walls
•  Ceramic Tile, Vitrified Tile And Natural Stone 
• Plywood Board
•  Gypsum Wall Board
• Cement Backer Board
•  Cement Terrazzo
•  Calcium Silicate Board 
•  Other Resilient Tile And Stone All Cement Based Surfaces Should Have Been Cured As Per Standard Practices And Shall Be Dry For Tiling Consult The Backer Board Manufacturer's Data Sheet For The Specific Recommendations And Load Bearing Capacity Of Specific Board Intended For Use.
• Note: Not For Use On Metallic And Plastic Substrates And For Metallic Tiles. Application Certifications For Commercial And Residential Interior Installations Of, Ceramic Tile, Semi Vitrified Tile And Natural Stone Of Size Not More Than 600Mm X 600Mm, Over Most Drywall Boards And Clean Dry Cement-based Surfaces. Used Where Installations Must Resist Physical Abuse, Shock, And Mild Chemicals. 

Colour: Off White

MYK Laticrete Super Set is a cement slurry enhancer and fortifier, particularly useful in tile and stone installation. It's a liquid product that strengthens cement slurry, making it suitable for both interior and exterior applications
Colour: White liquid

It is a polymer-based tile adhesive for fixing small to medium-format ceramic, semi-vitreous tiles and small-format natural stones on dry interior floors and walls.COLOR: GREY AND WHITE

Additional Information:

• Production Capacity: 1000
• Delivery Time: Immediate

A polymer-based, sanded cement tile grout for interior and exterior tile joints.

Colour: Available in a range of colours

SUPER SET® IWP is an integral waterproofing admixture with high-performance additives for high workability and water resistance for cement-based mortar, plaster, screed and concrete.

• 100% Stainfree
• Strong And Durable
• Chemical And Temperature Resistant
• Anti-bacterial And Anti-fungal

A High Performance Polymer Based Adhesive to Be Mixed With Water or Latex for InstallingMedium & Large Format Ceramic Tiles, Vitrified Tiles, Marble and Stone on Floors and Walls. Combine With Laticrete® 73 Crete Admix for Improved Performance.

Features & BenefitsFor Fixing Ceramic, Vitrified Tiles & Natural Stone on Interior Floor & WallIdeal for Tile-on-tile & New Floor TilingHigh Bond StrengthSingle Component - Just Add WaterProduct Details
Packaging 20 Kg & 50 Kg Bags    Coverage Approx. 55-60 Sq.ft. Per 20 Kg Bag With a 1/4" X 1/4" (6mm X 6mm) Square Notch Trowel for a Bed of 3mm. Color Grey & White CertificationAnsi: a 118.1 TEn: En12004 / Iso 13007 : C1tIs 15477:2019: Type 2  T AdhesiveVoc:practically NilHow to Apply
Substrate: the Surface to Be Covered With Ceramic Tile Shall Be Sound and Confirm to Good Design, Rigid, Clean and Free of Dirt, Oil, Grease, Curing Compounds, Form Release Agents or Loose Plaster and Paint. For Economy the Surfaces Should Be Level and True With in: Walls – 3mm in 2.5m Floors – 1.5mm in 1.0m Surface Preparation:If a Plaster/leveling Mortar Bed is Applied, Ensure That It is Cured for at Least 7 Days to Achieve Proper Strength Before Application of Tile Adhesive for Installation of TileEnsure the Substrate is Clean and Free From Impurities Like Dust, Dirt, Debris, Oil, Grease, Curing Agents, Loose Plaster EtcDampen the Wall Before Application of Thin Set AdhesiveClean the Back of Tile for Any Dust or CoatingMixing: the Products Can Be Mixed by Hand or Slow Speed Electric Drill Mixer (Less Than 300 Rpm). Pour Potable Clean Water in a Clean Container and Then Add the Powder Laticrete® 290 and Mix Until the Mixture Becomes Creamy and Plastic. Do Not Over Mix. Leave the Mix to Slake for 5-10 Min and Remix Before Use. Mix Only Sufficient Quantity of Adhesive for Immediate Need. Proportion: Approximately 1 Bag of Laticrete® 290 With 5-6 Ltrs of Water. Adjust Quantity of Liquid to Obtain Proper Consistency. Installation:Wet the Surface and Remove the Excess Water Before Applying the Adhesive. Ensure the Area is Shaded From Sunlight. The Adhesive Shall Be Applied With the Flat Side of the Trowel Using a Scraping Motion to Work the Material Into Good Contact With the Surface to Be Covered.Additional Mortar is Then Applied With the Notched Edge of the Trowel.When Installing Large Tiles, Spread Adhesive Onto Back of Tile in Addition to Trowelling Material Over Surface to Be Tiled. Select Proper Type of Notched Trowel.A) Thin Tiles Upto Size 300 X 300 Mm (1'x1'), Use a Square Notched Trowel of Size 6mm X 6mm to Provide a Total Thickness of 3mm
B) Large Porcelain Tiles Upto 450 X 450 Mm With Ribs, Use a Square Notched Trowel of Size 6mm X 6mm and Back Butter the Tiles With the Same Adhesive to a Thickness of 1-1.5mm to Provide a Total Thickness of 4.5mm
C) Large Porcelain Tiles Upto 600 X 600 Mm (2'x2') With Ribs, Use a Square Notched Trowel of Size 6mm X 9mm and Back Butter the Tiles With the Same Adhesive to a Thickness of 1-1.5mm to Provide a Total Thickness of 6mm
The Most Important Standard to Keep in Mind is to Insure That the Piece of Tile is Completely Bedded in the Mortar or Adhesive With 100% Coverage.Rear Face of Tiles (Especially Porcelain Tiles) Should Be Cleaned With Damp Sponge to Clean All the Dust. Do Not Saturate in Water.Excess Mortar on Adhesive Shall Be Cleaned From the Surface of the Stone With Wet Cloth or Sponge While the Mortar is Fresh.Areas of Application Designed for Interior Floor & Wall Areas Suitable SubstratesConcreteCement Mortar BedsExisting Tiling on Floor & Wall Ceramic Tiles and Stones (Best Results WhenMixed With Laticrete® 73 Mortar Admixture)Concrete MasonryCement PlasterBrick MasonryCement Terrazzo
COLOUR: GREY,WHITE

A high-strength, polymer-modified thin-set adhesive designed for large format tiles and natural stones.

Colour: Grey & White

Features:

For fixing tiles & stone on demanding external & internal applications 

Polymer modified bond with various substrates 

Water & shock resistant

Single component just add water

A multipurpose, polymer-modified powder offering vast utility including applications for floors & walls in interior & exterior areas. It is a cementitious thin-set powder to be mixed only with water to install various types of medium & large format tiles & stone on variety of substrates using thin-set method of installation.

For fixing tiles & natural stone on interior & exterior floor & wall

Polymer modified | Bonds with various substrates

Water & shock resistant

Single component - Just add water.

Coverage: Approx. 55-60 sq.ft. per 20 kg bag with a 1/4" x 1/4" (6mm x 6mm) square notch trowel for a bed of 3mm. Color: Grey & White Certification

ANSI: 118.4 ET, Meets EN 12004/ISO 13007: C2TE

ISI: TYPE 3 ADHESIVE

VOC:Nil

ubstrate: The surface to be covered with tile/ stone shall be sound and confirm to good design, rigid, clean and free of dirt, oil, grease, curing compounds, form release agents or loose plaster and paint. For economy the surfaces should be level and true with in: Walls – 3mm in 2.5m Floors – 1.5mm in 1.0m.

Surface Preparation:

If a plaster/leveling mortar bed is applied, ensure that it is cured for at least 7 days to achieve proper strength before application of tile adhesive for installation.

Dampen the wall before application of thin set adhesive

Fixing: The products can be mixed by hand or slow speed electric drill mixer (less than 300 rpm). Pour potable clean water in a clean container and then add the powder  laticrete 325 High Flex and mix until the mixture becomes creamy and plastic. Do not over mix. Leave the mix to slake for 5-10 min and remix before use. Mix only sufficient quantity of adhesive for immediate need.

Proportion: Approximately 1 bag of  laticrete 325 High Flex with 5-6 ltrs of water. Adjust quantity of liquid to obtain proper consistency.

Installation:

Wet the surface and remove the excess water before applying the adhesive. Ensure the area is shaded from sunlight. The adhesive shall be applied with the flat side of the trowel using a scraping motion to work the material into good contact with the surface to be covered.When installing large tiles, spread adhesive onto back of tile in addition to trowelling material over surface to be tiled. Select proper type of notched trowel.

a) Thin Tiles upto size 300 X 300 mm (1'X1'), use a square notched trowel of size 6mm X 6mm to provide a total thickness of 3mm
b) Large Porcelain Tiles upto 450 X 450 mm with ribs, use a square notched trowel of size 6mm X 6mm and back butter the tiles with the same adhesive to a thickness of 1-1.5mm to provide a total thickness of 4.5mm
c) Large Porcelain Tiles upto 600 X 600 mm (2'X2') with ribs, use a square notched trowel of size 6mm X 9mm and back butter the tiles with the same adhesive to a thickness of 1-1.5mm to provide a total thickness of 6mm

The most important standard to keep in mind is to insure that the piece of tile is completely bedded in the mortar or adhesive with 100% coverage.

Colour: Grey & White

Packing size: 5 kg, 20 kg

Latapoxy® 310 epoxy anchor adhesive is a two component non-sag high strength epoxy chemical anchor ideally suited for spot fixing or attaching marble or stone slabs on walls and for installing marble tiles or heavy tiles in ceilings. Latapoxy® 310 is ideal for external facades.
Features:
 
Non-staining
Withstands shock and vibration
Durable permanent bond
Ideal for use on dry or damp surfaces
Can be used for fabricating marble and stone assemblies
No clamps / mechanical anchor needed
Surface preparation:
Before using, store materials at room temperature for best working consistency. Low temperature will result in harder mixing. High temperature will shorten pot life of the material.
All surfaces must be sound, clean, free of oil, dust, wax, curing agents, laitance or any other contamination.
Concrete surfaces may be dry or damp during application. Other surfaces like glass, metal etc. Must be dry.
Mechanical scarifying or sanding by disk or water blasting is highly recommended to remove contamination or when application on old concrete, to remove carbonized layer.
Concrete slabs, at short distance from the sea shore, must be washed frequently from possible accumulated salts.
Application on steel and especially on stainless steel, may require diluted acid washing and/or sanding of the metal surface.
Mixing:
Combine equal volumes of part a and part b and mix thouroghly for 2-3 minutes until uniform colour.
Non uniform mixing will result in inferior material, sticky, staining, which will cure to reach the designed properties of the material. Properly mixed material, will not stain white or any bright colour marble.
Mixing of small quantities can be done by spatula, margin trowel or putty knife, larger quantities can be mixed with an electrical mixer at low speed.
Minimum application temperature is 5 °c .(40°f). Beware that working in temperatures over 35°c, shorten drastically the working time of the epoxy.
Application:
Dusted surfaces should be cleaned with a damp sponge or cloth.
Apply laticrete® 310 standard to back of stone in the form of dabs.
Place the stone on the surface and apply slight pressure to level and make contact between the two surfaces, and level to desired plane.
Make sure that under no circumstances, the thickness of the material, after in place, will be less than 6 mm. (epoxies generate heat while curing. If thickness is minimal, relative to bonding surface, heat loss to the surfaces is too quick, resulting in poorer performance of the cured material!)
The uncured material is water cleanable and can be easily cleaned from tools, surfaces or hand with water and nylon pad.
The material in non -toxic, but can develop a rash to sensitive skin. Good workmanship practice requires the use of gloves when working with epoxies.
Cured material can be removed only by mechanical means.
Colour: Off White

Clenza TS™ Tap and Shower Cleaner is a specialty cleaner designed to remove hard water stains, limescale stains and stubborn soap scum from CP fittings and sanitary ware.
Features and benefits:
Speciality cleaner for CP fittings & sanitary ware
Restore shine & gloss
Removes stubborn soap scum,  hard water stains and  limescale stains

How to apply:Application:
Gently shake the container and spray the cleaner on CP fittings, sanitary ware, basins etc.
Spread the cleaner with a soft scrubber and leave it for 1-2 minutes
Gently rub and rinse with water to get a glossy shine. For heavy stains, spray over the spots and rub with scrubber to spread followed by rinsing with water. Repeat the cleaning for better results. 

Caution: 
Do not mix with other household cleaners and acids. Keep out of reach of children. Do not swallow.

Myk Laticrete Tile Spacers is specially designed to create a uniform gap between tiles, this results in proper alignment throughout the tiling area.The Spacers are available in different width sizes starting from 2mm width to 10mm width.Spacers accommodate the movements due to thermal variations and different loads. When filled with the right grout material,they can efficiently reduce the free water flow/ leakage through the joints and also make the joints anti fungal and anti bacterial.It ensures longer life span of tile installation.

Colour: Yellow

Additional Information:

• Production Capacity: 24 month